Parts
Please excuse the quality of some pictures as they were gathered from websites
and standardized to fit this page.
Building a complete upper? You will need the following: Barrel, Receiver,
Charging Handle, Bolt Carrier Group, Handguard System, Gas Tube and Gas Block.
Muzzle devices are optional, but usually desired. Add $25 to the barrel for
muzzle threading and add $25 to assemble a complete upper with your specified
barrel and parts.
These are just a few parts that I commonly use. I can build with any parts you
specify.
Receivers
Armalite A3 |
$250 |
|
Typical flattop receiver with dustcover and brass deflector. |
DPMS A3 |
$200 |
|
DPMS flattop with dustcover, forward assist, brass deflector. |
Armalite A2 |
$??? |
|
Typical A2 type receiver with rear sight, dustcover, forward
assist and brass deflector. Only available with standard feed ramps. |
Bolt and Charging Handle Assemblies
Armalite Charging Handle |
$25 |
|
Armalite charging handle with basic type latch. |
Gas Buster |
$90 |
|
PRI M84L gas buster AR-10 charging handle with big latch. |
Extended charging handle latch |
$20 |
|
Badger "First Generation" extended latch. |
Extended charging handle latch |
$20 |
|
Badger "Second Generation" extended latch. |
308 Bolt Carrier Group |
$250 |
|
Armalite bolt carrier group for 308 case head sized cartridges. |
308 Bolt Carrier Group |
$250 |
|
DPMS bolt carrier group for 308 case head sized cartridges. |
Magnum Bolt Carrier Group |
$275 |
|
Armalite bolt carrier group for magnum case head sized cartridges. |
Magnum Bolt Carrier Group |
$275 |
|
DPMS bolt carrier group for magnum case head sized cartridges. |
308 Bolt |
$150 |
|
Armalite bolt for 308 case head sized cartridges. |
308 Bolt |
$150 |
|
DPMS bolt for 308 case head sized cartridges. |
Magnum Bolt |
$175 |
|
Armalite bolt for Magnum case head sized cartridges. |
Magnum Bolt |
$175 |
|
DPMS bolt for Magnum case head sized cartridges. |
Handguards
Carbine Tube |
$100 |
|
Basic DPMS carbine length aluminum free float handguard tube. |
Rifle Tube |
$110 |
|
Basic DPMS rifle length aluminum free float handguard tube. |
Carbon Fiber Carbine Tube |
$90 |
|
DPMS carbine length carbon fiber free float handguard tube. |
Carbon Fiber Rifle Tube |
$100 |
|
DPMS rifle length carbon fiber free float handguard tube. |
Daniel Defense 7.0 |
$275 |
|
Daniel Defense carbine length quad railed handguard. 8.5 oz. |
Daniel Defense 9.0 AR-10 Lite Rail |
$375 |
|
Mid length quad railed handguard for the AR-10. 13.5 oz. |
Daniel Defense 12.0 AR-10 Lite Rail |
$425 |
|
Rifle length quad railed handguard for the AR-10. 18.5 oz. |
Daniel Defense 14.0 AR-10 Lite Rail |
$Call |
|
Extended length quad railed handguard for the AR-10. 20.5 oz. |
LaRue 13.2 AR-10 |
$330 |
|
LaRue AR-10 extended length quad railed handguard. 19oz. |
PRI 7.0 |
$315 |
|
PRI carbine length Gen III handguard, natural finish. Black
finish is also available and shown on the rifle length version below. |
PRI 9.0 |
$315 |
|
PRI mid-length Gen III handguard, natural finish. Black finish
is also available and shown on the rifle length version below. |
PRI 12.0 |
$320 |
|
PRI rifle length Gen III handguard, black finish. Natural finish
is also available and shown on the 2 versions above. |
JP 12.0 |
$150 |
|
JP Enterprises has a variety of handguards available, this is
the black rifle version, but I can get any of them. |
JP 7.0 |
$150 |
|
JP Enterprises has a variety of handguards available, this is
the black carbine version, but I can get any of them. |
Badger Ordinance 7.0 |
$150 |
|
Badger's flat bottomed "stabilizer" handguard in carbine length. |
Badger Ordinance 12.0 |
$160 |
|
Badger's flat bottomed "stabilizer" handguard in rifle length. |
Gas System
Gas Tube |
$15 |
|
Specify Pistol, Carbine, Mid-Length, Rifle length or Extended
length. |
Shaved Gas Block |
$40 |
|
Simple 0.750" aluminum gas block. Fits under
most handguards. |
Bull Barrel Gas Block |
$40 |
|
Simple 0.940" aluminum gas block. Fits under most
handguards. 1.6oz |
Railed Gas Block |
$40 |
|
DPMS 0.750" aluminum gas block with a picatinny rail on top.
2.5oz |
Bull Barrel Railed Gas Block |
$40 |
|
DPMS 0.940" aluminum gas block with a picatinny rail on top. |
Quad Railed Gas Block |
$50 |
|
DPMS 0.750" aluminum gas block with a 4 picatinny rails.
3.4oz |
Steel Railed Gas Block |
$40 |
|
Stag 0.750" steel gas block with a picatinny rail. 5.1oz |
AR-10T Stainless Steel Railed Gas Block |
$50 |
|
Armalite 0.875" stainless steel gas block with a picatinny rail.
4.4oz |
JP 0.750" Adjustable |
$70 |
|
JP Enterprises original adjustable gas block in anodized
aluminum. 1.9oz |
JP 0.750" Shaved Adjustable |
$80 |
|
I take a 0.750" JP aluminum block and turn it down to fit under
a handguard tube. You need this on any barrel where the gas port/block is
covered by the handguard tube such as 300x221 or dissipater setups. |
JP 0.940" Adjustable |
$80 |
|
JP Enterprises adjustable gas block for bull barrels,
aluminum. 2.5oz |
JP 0.940" Shaved Adjustable |
$90 |
|
I take a 0.940" JP aluminum block and turn it down to fit under
a handguard tube. You need this on any barrel where the gas port/block is
covered by the handguard tube such as 300x221 or dissipater setups. |
LaRue Low Profile |
$70 |
|
Steel 0.625" low profile gas block made by LaRue Tactical.
3.9oz |
LaRue Low Profile |
$70 |
|
Steel 0.750" low profile gas block made by LaRue Tactical.
2.8oz |
LaRue Low Profile |
$70 |
|
Steel 0.875" low profile gas block made by LaRue Tactical.
2.8oz |
AR15barrels Low Profile |
$55 |
|
Steel 0.625" lightweight low profile adjustable gas block.
1.3oz |
PRI Low Profile |
$55 |
|
Steel 0.750" low profile gas block made by PRI. 1.4oz |
YHM Low Profile |
$40 |
|
Steel 0.750" low profile gas block made by YHM. 4.4oz |
YHM Specter |
$40 |
|
Steel 0.625" low profile clamp-on gas block made by YHM
allows profiles to be larger than 0.625" in front of the gas block. 5.5oz |
YHM Specter |
$40 |
|
Steel 0.750" low profile clamp-on gas block made by YHM
allows profiles to be larger than 0.750" in front of the gas block. 4.4oz |
YHM Dual Rail |
$65 |
|
Steel 0.750" dual rail gas block by YHM
allows profiles to be larger than 0.750" in front of the gas block. 7.2oz |
PRI Flip-Up Front Sight, clamp-on, 0.625" or 0.750"
0.750" model is 4.6 oz. |
$180 |
|
Flip-up front sight that clamps on to the barrel.
Picture Picture |
Flash Hiders, Brakes & Comps
A2 |
$10 |
|
Your plain jane military A2 flash hider / comp, 1/2"-28 threads. Requires indexing. |
A1 |
$10 |
|
Military A1 "Birdcage" flash hider, 1/2"-28 threads. No indexing
required. |
Three Prong |
$10 |
|
Old School military flash hider, 1/2"-28 threads. No indexing
required. |
Stag Comp |
$15 |
|
Stag Arms basic 3 port comp, 1/2"-28 threads. Requires
indexing. |
Phantom |
$30 |
|
YHM standard 4 port phantom flash hider, 1/2"-28 threads.
No indexing required. |
Phantom 5C1 |
$30 |
|
YHM phantom flash hider with a closed bottom port, 1/2"-28
threads. Requires indexing. |
Phantom 5C2 |
$30 |
|
YHM phantom flash hider with a closed bottom port, 1/2"-28
threads. Requires indexing. |
308 Phantom |
$35 |
|
YHM phantom flash hider for 6.8 SPC and 308, 5/8"-24
threads. No indexing required. |
308 Phantom 5C1 |
$35 |
|
YHM phantom flash hider with a closed bottom port for 6.8 SPC and 308, 5/8"-24
threads. Requires indexing. |
308 Phantom 5C2 |
$35 |
|
YHM phantom flash hider with a closed bottom port for 6.8 SPC and 308, 5/8"-24
threads. Requires indexing. |
Vortex |
$50 |
|
Smith Enterprises 5.56 Vortex G6 flash hider, 1/2"-28 threads.
No indexing required |
Vortex |
$60 |
|
Specially made Smith Enterprises Vortex G5 30 caliber flash hider, 9/16"-24 threads for 6.8 SPC and 30 caliber barrels. Same diameter at the 5.56 version (0.860"), but there is no skirt on rear. No indexing required |
308 Vortex |
$85 |
|
Smith Enterprises 6.8 SPC and 308 Vortex G6 flash hider, 5/8"-24 threads.
No indexing required |
Miculek Comp |
$50 |
|
DPMS manufactured 1/2"-28 threads. Requires indexing. |
308 Miculek Comp |
$65 |
|
DPMS manufactured for 6.8 SPC and 308 with 5/8"-24 threads. Requires indexing. |
MSTN QC Comp |
$80 |
|
Stainless steel with 5/8"-24 threads. Requires
indexing. |
Black MSTN QC Comp |
$82 |
|
Blackened stainless with 5/8"-24 threads. Requires
indexing. |
Bennie Cooley Comp |
$90 |
|
JP Enterprises stainless steel with 1/2"-28 threads. Requires
indexing. |
Big Bennie Cooley Comp |
$90 |
|
JP Enterprises stainless steel with 5/8"-24 threads. Requires
indexing. |
Fat Bennie Cooley Comp |
$90 |
|
JP Enterprises stainless steel with 5/8"-28 threads. Sized
to work on a bull barrel. Requires
indexing. |
JP Recoil Eliminator |
$115 |
|
JP Enterprises stainless steel with 3/4"-28 threads. Sized
to work on a bull barrel. Requires
indexing. |
OPS INC Brake |
$115 |
|
OPS INC stainless steel brake. Available with 1/2"-28, 9/16"-24
or 5/8"-24 threads. Requires
indexing. |
|